这是本文档旧的修订版！

ESPHome Smart Light Bulb

Introduction – Detected by Home Assistant

– Controlled by MQTT, Web UI, HTTP, etc

– Using times, scripts, rules

– Open source

– Use ESP8285-2M as MCU

Specification – RGB+C+W, 9W

– 850LM

– AC:100-265V, 50/60Hz

– 2700-6500K

– E26/E27

– 60 x 60 x 125 mm

– 40000 hours

GPIOs

GPIO4 – PWM1 – Cool WhiteGPIO5 – PWM4 – Blue ColorGPIO12 – PWM2 – Red Color GPIO13 – PWM5 – Warm WhiteGPIO14 – PWM3 – Green Color

Yaml File:

ssubstitutions: name: “aiyato-rgbcw” friendly_name: “AiYaTo RGBCW” project_name: “doit.aiyato-rgbcw” project_version: “1.0.0” light_restore_mode: RESTORE_DEFAULT_ON color_interlock: 'true'

esphome: name: “${name}” name_add_mac_suffix: true project: name: “${project_name}” version: “${project_version}”

preferences: flash_write_interval: 1min

esp8266: board: esp8285 restore_from_flash: true

globals: - id: my_global_mode type: bool restore_value: no initial_value: 'true'

logger:

api:

ota: safe_mode: false

wifi: ap: {}

interval: - interval: 1s then: - lambda: |- static uint32_t cnt = 0; static int flag = 0; static ESPPreferenceObject pref = global_preferences→make_preference<uint32_t>(23332500UL, true); if¹⁾) { flag = 0; ESP.restart(); } if(cnt == 0){ cnt++; uint32_t val = 0; pref.load(&val); val+=1; pref.save(&val); global_preferences→sync(); if(val >= 3){ my_global_mode→value() = false; } }else if(cnt < 5){ cnt++; if(cnt == 5){ uint32_t val = 0; pref.save(&val); global_preferences→sync(); } } if(!my_global_mode→value()){ if(cnt == 1){ char a[] = “000000”; char b[] = “000000”; wifi_wificomponent→clear_sta(); wifi_wificomponent→save_wifi_sta(a, b); wifi::WiFiAP wifi_wifiap = wifi::WiFiAP(); wifi_wificomponent→set_ap(wifi_wifiap); wifi_wificomponent→set_ap_timeout(5000); flag = 1; rgbww_rgbwwlightoutput→set_color_interlock(false); } static int state = 0; auto call = id(my_light).turn_on(); call.set_transition_length(1000); call.set_brightness(1.0); if (state == 0) { call.set_rgb(1.0, 0.0, 0.0); call.set_cold_white(0.0); call.set_warm_white(0.0); } else if (state == 3) { call.set_rgb(0.0, 1.0, 0.0); } else if (state == 5) { call.set_rgb(0.0, 0.0, 1.0); } else if (state == 7) { call.set_color_brightness(0.0); call.set_cold_white(1.0); call.set_warm_white(0.0); } else if (state == 9) { call.set_cold_white(0.0); call.set_warm_white(1.0); } else if (state == 11) { call.set_color_brightness(1.0); call.set_rgb(0.0, 1.0, 0.0); call.set_cold_white(0.0); call.set_warm_white(0.0); } call.perform(); state += 1; if (state == 12) { my_global_mode→value() = true; } }

web_server: port: 80

captive_portal:

binary_sensor: - platform: status name: “${friendly_name} Status”

sensor: - platform: uptime update_interval: 60s name: “${friendly_name} Uptime”

button: - platform: restart name: “${friendly_name} Restart”

output: - platform: esp8266_pwm id: red_output pin: GPIO12 - platform: esp8266_pwm id: green_output pin: GPIO14 - platform: esp8266_pwm id: blue_output pin: GPIO5 - platform: esp8266_pwm id: cold_white_output pin: GPIO4 - platform: esp8266_pwm id: warm_white_output pin: GPIO13

light: - platform: rgbww name: “${friendly_name}” restore_mode: “${light_restore_mode}” red: red_output green: green_output blue: blue_output cold_white: cold_white_output warm_white: warm_white_output cold_white_color_temperature: 6000 K warm_white_color_temperature: 3000 K color_interlock: “${color_interlock}” id: my_light

text_sensor: - platform: wifi_info ip_address: name: “${friendly_name} IP Address” disabled_by_default: true

Note: 1.How to restore the device. A: —With Button：Long-Press button over 5 seconds

   — Without Button：Reset the device over 3 times with an interval of no more than 5 seconds each time.
   The device will self-test it and release the AP SSID about 5 seconds later.

2.HA control A: Power the device, the light product will light up even though you software-shutdown it. And the other product will keep the last device state. 3.OTA upgrade A: In browser, land “aiyato-xxxx-xxxxxx” or IP address found in Wi-Fi router background. Enjoy it with ESPHome plugin or YAML file.

4.Manually add device to HA A: If HA does not automatically discover device, add integration in the lower right corner of the Devices & Services page, search for ESPhome, and enter the following host address: aiyato-xxxxx-xxxxx (xxxxxx is MAC address of your device) or you can view the IP address of the device on the router management page. Retain the default port number “6053” and submit the configuration. 5. When to save the device state A: Device state updates automatically every ONE minute. 6. ESPHome ONLY support 2.4GHz Wi-Fi router ✨DON'T MISS OUT:AiYaTo: ESPHome Smart RGBCW Light Bulb Works With Home Assistant 9W E27 ESP8285 HA PRODUCT PROPERTY:✨ 1: Dohome is a professional brand.Product original from cn(origin).

REASONS TO BUY:✨ Esphome: the rgbc light bulb is equipped with an esphome app, which can be easily connected to your home or office. ✨ Bulb home assistant: you can easily plug in and unplug the light bulb from your rgbcw home assistant, by replacing the battery or installing the bulb. ✨ Recommended seller: the rgb led light bulb is recommended by professional designers, as well as industry-leading manufacturers. it is recommended to use at home or in the office when you have high-end products. ✨ Design with care: this rgbc light bulb is made of high-quality abs material, which is durable and has a long service life. ✨ Extremely convenient: the rgbcw light bulb is easy to use and can be used for home, office, classroom, etc.

BUYER SAYS:✨ One out of four is bad.